zgarda dresaj caine cu telecomanda lcd antilatrat comportament electrica
-
Produs:Nou, Fără garanție
-
Numar articol:193728685
-
Disponibilitate:Indisponibil
-
Preț:140,00 Lei
-
Anuntul a expirat la:10.11.2020, 00:30
-
Ai o nelamurire?
-
Vandut de:
-
Vinde si tu:Pune in vanzare un produs ca acesta
-
Optiuni:
Descriere
Vânzatorul este direct răspunzator pentru produsul afișat în această pagină.
Disponibilitate: Indisponibil - Vezi produse similare
Specificatii
1. 100 levels of vibration.
2. 100 levels of static (optional)---You can gradually increase the
vibration or static shock level from 1 to 100 as you wish. Level 1
is the most soft level and level 100 is the opposite ,you should
change the level depending on the endurance and reaction of your
dog in response to the stimulation.
3. The levels can be altered by use of up & down button.
4. A tone button activates a tone on the receiver.
5. This system is used for only 1 receiver.
6. The receiver will TURN OFF if it is unused for 4
minutes.
7. Any movement will activate the receiver into STANDBY
MODE.
8. The transmitter will go into STANDBY MODE if there is no
operation after 20 seconds and turn off after 2 minute.
9. Adjustable belt length, maximum diameter of 18cm, fit the dog
with neck size from 1 to 18 inches. Two pairs of metal prong
(short/long) to suit dogs with varied fur thickness.
User Manual for Transmitter:
1. To install the batteries, open the battery cover, which is at
the back of the transmitter.
2. Install the battery (2 x 4LR44/ 6V) in the transmitter and
ensure the polarity is correct.
3. The transmitter will be TURN ON automatically.
4. Press the buttons one by one - the LCD images will
change.
5. Press the up and down buttons on right hand side to set level.
.
6. The LED light can be used for giving training
signals.
7. The transmitter will go into STANDBY MODE if not operated for 20
seconds and will TURN OFF if not operated for 2 minutes.
8. In STANDBY MODE, press any button (except LED light button) to
wake it up.
9. To TURN ON the transmitter, hold mode button for at least 5
seconds.
User Manual for the Receiver and Code:
1.To install the batteries
2.Remove the cover
3.Install the batteries (2xAAA 1.5V), make sure the polarity is
correct
4.There is a beep right after installing the batteries in the
receiver
5.Go to the transmitter and choose 1 or 2 channel to encode by
pressing the channel button 1/2 in the transmitter
6.Then press the LAUNCH button on transmitter
immediately
7.The receiver will beep - it is now encoded to the
transmitter
8.Replace cover and tighten metal probes
Specification-Collar
Length: 43mm Height: 68mm Width: 38mm
Collar length adjustable from 35cm to 58cm
Weight: 56g (module + battery)
Power: 2 x 1.5V AAA battery (included)
Specification-Handset
Length: 25mm Height: 83mm Width: 45mm
Weight: 40g (with battery)
Power: 2 x 4LR44/ 6V (included)
LED signal light and illumination at night
The sound function for attracting attention
Modalitati de livrare si plata
LIVRARE
In Bucuresti
-
- Predare personala - regie in max. 2 zile lucratoare
PLATA
- - La predare
- - Ramburs
Politica de retur
- - Produsul nu se poate returna.