Regulator solar. Controler solar panouri solare Regulator de incarcare JUTA MPPT 12v 10 A. Tehnologie MPPT

Un controler cu tehnologie MPPT creste eficienta panourilor solare cu pana la 30%.

The most outstanding feature of Maximum Power Point Tracking controller is intelligent tracking input voltage from solar panel, which could let solar panel always working at Maximum Power Point of V-A curve. Compared with normal solar charge controller, this MPPT controller could increase 10%-30% electrical power using efficiency from solar panel.

Function: This MPPT controller is not only have above mentioned special function, at the same time including completely Protecting and Controlling functions:

Overcharge protection
Over-discharge protection
Battery Reverse Current Protection
Overloading Protection
Short Circuit Protection
Reverse Polarity Connection Protection

Schematic Diagram: Picture 2 shows typical 12V battery solar charge system V-A curve.

Normal Solar Charge Controller: Solar Panel works at point A state, the solar panel working voltage is a little higher than battery voltage.
Charge Voltage: UA=13.2V
Charge Current:: IA=9.8A
Charge Power: PA=13.2*9.8=129.36w

MPPT Solar Charge Controller: Solar Panel works at point B state, the solar panel working voltage much higher than battery voltage.
Charge Voltage: UB=18.4V, 
Charge Current::  IB=9.3A  
Charge Power: PB=18.4*9.3=171.12w  
Area in drawing: ①＋②

Comparison: The power B is more than power A..
△P/ PA =（PB— PA）/ PA＝32..3%
As a result of different manufacture of solar panels, different solar illumination intensity, different temperature, different efficiency of solar charge controller and so on. The effective power increase rate is 10-30%.

Form a complete set: 
Solar Panel: 12V solar system should use 40pcs cells laminated solar panel. The maximum power point voltage is18V above. 24V solar system should use 2pcs above mentioned solar panels. 48V solar system should use 4pcs above mentioned solar panels.
Conductor: The cable between solar panel with MPPT solar charge controller should be better calculated by 1Ampere per 1mm².
Solar Charge Controller: MPPT-10 Model solar charge controller Rated input Ampere is 10A. We have 12V, 24V and 48V three kinds of MPPT solar charge controllers (other specifications could be designed as customer special request). Fit for power of solar panels: 20—200Wp（12V）, 40—400Wp（24V）, 80-800Wp (48V).

Connection: ( As Picture 3 according to below process)

1. Connected the “+”, “-” poles of the battery to the controller ( 3, 4 from left) firmly and correctly. At this time the LOAD green LED is bright. If the LOAD green LED is not bright, it is indicate there is battery reverse polarity connection. Only LOAD green LED is bright, we could continue next step operation.
2. Connected the “+”, “-” poles of the solar panel to the controller (1,2 from the left) firmly and correctly.
3. Connected the “+”, “-” poles of the LOAD to the controller (5,6 from the left) firmly and correctly.

Simply Measure Methord: For 12V system, measure the input voltage from solar panel with multimeter (terminal 1, 2 of controller), it is normal if the voltage of solar panel more than battery voltage 0.5-6V. Generally, the higher input voltage, the better charge efficiency. For 24v and 48V system, the input 
voltage will be much more higher than battery voltage
(Note: It is normal the controller can not find Maximum Power Point within 10 minutes from system start.)
Indicator: (Picture 1)

1. Load indicator, green, bright indicate there is output, Load could work, “off” indicate there is not output, Load can not work.
2. Low Voltage Indicator, red, bright indicate the voltage of the battery is low. Load could not normal working. This is normal phenomenon. When the battery voltage recovers to 12.6V or (25.2v), the Load will be automatically working, at this time the indicator is off.
3. Charge Indicator, red, bright indicate the battery need to charge, flickering means float charging, off means charge has stop.

RESET Button: The rated output current of this MPPT solar charge controller is 10A, if there is short circuit or overload happened, the MPPT controller will close output. ( Load indicator off, Low voltage indicator off.)
If you need the MPPT controller recover work, please check the reasons and clear out the fault firstly. Then put a small stick such as toothpick, ball-pen tip inside the RESET hole, and press RESET button will be OK.

MPPT-10 Data Sheet

• Model:MPPT-1012
• Rated Voltage:DC12V
• Max Current:10A
• Zero Loaded Losses:≤45mA/12V
• Full Charge Cut:14V/12V
• Low Voltage Cut:10.5V/12V
• Supply Resume Voltage:12.6V/12V
• Temp Compensation:-3mV/ceII
• Efficiency:95％～97％
• Min. Wire Size:1～2A/ mm^2
• MPPT Efficiency Increase:10～30﹪
• Net Weight:0.55Kg
• Dimension:188×93×55mm

In licitatiile nostre gasiti si ALTE TIPURI  de REGULATOARE  precum si PANOURI FOTOVOLTAICE si ACCESORII :

http://magazine.okazii.ro/coroama2222/panouri-solare-fotovoltaice-si-accesorii

http://www.okazii.ro/catalog?per_page=200&foto=1&user_list=coroama2222&list_view_type=more

Livram promt in toata tara prin Posta Romana sau Fan Curier .

   Impachetarea si livrarea se face in maxim 24 ore de la primirea comenzii !

 *** Pentru al doilea, al treilea sau mai multe produse  comandate  transportul este gratuit !.

Nu licitati numai pentru date de contact fara sa achizitionati produsul, fiecare licitare se comisioneaza .

Va rugam nu acordati calificative negative, fara a discuta in prealabil, orice problema se va rezolva .