Numar articol: 198578886. Vezi produse asemanatoare.
Pune in
vanzare un produs ca acesta
Interfata diagnoza VAG COM VCDS v 22.10 EN - HQ - Vw Audi Skoda Seat 2023
Cost unic de transport la toate comenzile acestui vanzator
Disponibilitate:
In stoc
2 disponibile
Produs:
Nou, Certificat de garanție 6 luni
Politica de retur:
Acest produs poate fi returnat in 14 zile
Detalii
Plata:
- La predare
- Ramburs
- Avans
100% pozitive
(din 2469
)
)
Descriere
Raporteaza produsVânzatorul este direct răspunzator pentru produsul afișat în această pagină.
Specificatii
Nota: Ultima versiune de soft
disponibila este v22.10 ROMANA +
ENGLEZA
VCDS 19.6 este cea mai recenta
versiune 2019 !
Interfata
VCDS este dedicata autoturismelor din gama VAG ( VW, Audi, Skoda,
Seat).
Aceasta versiune, suporta codari (Long Coding).
Chip Edition: ATMEGA162 + FT232RL + L9637D + 16V8B.
Calitatea Pieselor din interiorul testerului este: A+. Interfetele de diagnoza nu au in componenta procesoare NEC .
Atentie! Pentru necunoscatori, acesta este un instrument de diagnoza si nu unul de corectat/ajustat kilometrii.
Versiune software: 19.6 Limba Engleza
Suporta urmatoarele branduri de autoturisme: Volkswagen, Audi, Skoda, Seat.
Este compatibila cu toate modelele ale brandurilor enumerate mai sus.
Caracteristici:
- simplitate la instalarea softului
- functioneaza pe autoturisme VW AUDI SKODA SEAT produse pana in prezent (2019)
- a fost extins numarul de coduri de defect cunoscute dar si numarul de parametrii in timp real
- imbunatatiri aduse in meniul de masuratori avansate
- suporta codurile de acces securizate formate din 6 caractere
- a fost optimizata viteza HEX-NET Turbo
- optimizare pentru low-level timing
- imbunatatiri majore ale firmware-ului
- imbunatatita viteza protocolului UDS
- rezolvat problema cu SRI reset
- multe alte mici imbunatatiri fata de versiunile precedente.
- peste 20.800 coduri de eroare
- suport pentru noile Gateway-uri MQB / Mk.7 , 4G Audi A6
- se pot trasa grafice si stoca informatii in timpul mersului
- compatibil cu auto mai vechi ce folosesc K-line, L, K+L, Dual-K, cele pe CAN (automobilele dupa 2004), cat si cele pe UDS (dupa 2010)
Functii VCDS 19.6:
- Citeste, interpreteaza si sterge codurile de eroare (Diagnostic Trouble Codes) pe motor si module auxiliare
- editeaza si vizualizeaza parametrii masinii in timp real,
- citeste kilometri reali din ECU (EDC 15 si EDC 16),
- ofera posibilitatea de a programa functii ascunse ale inchiderii centralizate, luminile de pe bord, dome light, sau follow me home, schimbarea limbii computerului de bord,
- adaptarea clapetei de acceleratie,
- modificarea pozitiei de referinta pentru Xenon,
- modificarea distantei senzorilor de parcare,
- modificarea turatiei la relanti,
- modificarea cantitatii de combustibil injectate in cilindrii la relanti
- testarea si verificarea in timp real a functionalitatii injectoarelor si a sistemului de injectie si a tuturor senzorilor motorului, cutiei de viteze, a sistemului de aer conditionat si multe multe altele!
- compatibil cu autoturisme mai vechi ce folosesc K-line, L, K+L, Dual-K,
- compatibil cu cele care necesita protocolul CAN (automobilele dupa 2004)
- diagnoza, adaptare, recodare pe module Motor, Airbag, ABS, Clima, A/C, Radio, Navi, Servodirectie, Confort, etc;
VCDS poate fi folosit atat de incepatori cat si de cei avansati ! Cu ajutorul acestuia puteti diagnostica masini mici din 1992 pana in prezent 2019.
Sisteme de Operare compatibile: Windows XP, Vista, 7, 8, 8.1, 10 (32 biti si 64 biti) .
Pachetul
include:
- Interfata VAG COM 19.6
- CD cu soft in limba engleza
- Interfata VAG COM 19.6
- CD cu soft in limba engleza
|
|
VCDS 19.6 Diagnostic cable new
added functions:
-Support for MLB2 platform cars (HEX-NET interface recommended)
-Support for 2019 and early model cars
-Greatly expanded the amount of DTC Freeze-Frame data displayed
-Improvements in Advanced Measuring Value Selection Window
-Display of factory identifiers instead of arbitrary location numbers
-Support for Six-Digit security access codes
-HEX-NET Turbo and other speed optimizations
-Optimized low-level timing routines and CPU core affinity
-Major firmware enhancements for HEX+CAN and Micro-CAN interfaces
-Improved UDS mapping speed and reliability when subchannels are present; progress indicators.
-Fixes SRI reset in newer Crafter instruments.
-New ASAM data and Label Files
-Support vehicle list: For AUDI VW SEAT SKODA
Vagcom v19.6 cable New Features:
Auto Scan 1001.01
1. Control module unit information
2. Read fault codes 004.01
3. Output test 005
Selective output test 005
4. Basic settings 006
5. Clear DTCs 004.10
6. Close control module 022
7. Pairs of coding control module (brush hidden) 007 (service 1A)
008 (Service 22) From the station control module 007 coding (service 1A)
008 (Service 22) Read measured value block 08 010.02 (KWP1281)
8. Advanced measurement reading
9. channel read 010.01
10. matching 012 014 (long)
11. Log (Known under KWP-2000 * Coding II) 015.01
12. View readiness 020.01 Guided ready state settings
13. security access 015.02
14. All supported DTCs
15. Common OBD-II function
16. Fault environmental data
17. Dual K-Line Support 7-PIN code 020.07
18. Upgrade to the latest fault code library
19. Direct CAN line diagnosis (Need to support diagnostic cables CAN line diagnosis)
20. Modes of transport 1001.03 (on)
1001.04 (off) (Need to support diagnostic cables CAN line diagnosis)
21. Advanced measurement block
22. Support for dual engine control module
Compared to the previous version, the VAG 19.6 main changes is BUG fixes and improvements.
Vagcom v19.6 Basic functions:
00 Auto Scan
01 control module unit information
02 read fault codes
03 Output Test
Selective output test (only for KWP-2000 *)
04 Basic settings
05 clear DTCs
06 Close Control Module
07 pairs of coding control module
Slave control module for coding (only for KWP-2000 *)
Read measured value block 08
09-channel read (applies only to KWP-1281 *)
10 matching
11 Log (known under KWP-2000 * Coding II)
15 View Ready
16 security access (only for KWP-2000 *)
18 All supported fault codes (only for KWP-2000 *)
33 Common OBD-II function
-Support for MLB2 platform cars (HEX-NET interface recommended)
-Support for 2019 and early model cars
-Greatly expanded the amount of DTC Freeze-Frame data displayed
-Improvements in Advanced Measuring Value Selection Window
-Display of factory identifiers instead of arbitrary location numbers
-Support for Six-Digit security access codes
-HEX-NET Turbo and other speed optimizations
-Optimized low-level timing routines and CPU core affinity
-Major firmware enhancements for HEX+CAN and Micro-CAN interfaces
-Improved UDS mapping speed and reliability when subchannels are present; progress indicators.
-Fixes SRI reset in newer Crafter instruments.
-New ASAM data and Label Files
-Support vehicle list: For AUDI VW SEAT SKODA
Vagcom v19.6 cable New Features:
Auto Scan 1001.01
1. Control module unit information
2. Read fault codes 004.01
3. Output test 005
Selective output test 005
4. Basic settings 006
5. Clear DTCs 004.10
6. Close control module 022
7. Pairs of coding control module (brush hidden) 007 (service 1A)
008 (Service 22) From the station control module 007 coding (service 1A)
008 (Service 22) Read measured value block 08 010.02 (KWP1281)
8. Advanced measurement reading
9. channel read 010.01
10. matching 012 014 (long)
11. Log (Known under KWP-2000 * Coding II) 015.01
12. View readiness 020.01 Guided ready state settings
13. security access 015.02
14. All supported DTCs
15. Common OBD-II function
16. Fault environmental data
17. Dual K-Line Support 7-PIN code 020.07
18. Upgrade to the latest fault code library
19. Direct CAN line diagnosis (Need to support diagnostic cables CAN line diagnosis)
20. Modes of transport 1001.03 (on)
1001.04 (off) (Need to support diagnostic cables CAN line diagnosis)
21. Advanced measurement block
22. Support for dual engine control module
Compared to the previous version, the VAG 19.6 main changes is BUG fixes and improvements.
Vagcom v19.6 Basic functions:
00 Auto Scan
01 control module unit information
02 read fault codes
03 Output Test
Selective output test (only for KWP-2000 *)
04 Basic settings
05 clear DTCs
06 Close Control Module
07 pairs of coding control module
Slave control module for coding (only for KWP-2000 *)
Read measured value block 08
09-channel read (applies only to KWP-1281 *)
10 matching
11 Log (known under KWP-2000 * Coding II)
15 View Ready
16 security access (only for KWP-2000 *)
18 All supported fault codes (only for KWP-2000 *)
33 Common OBD-II function
Galerie foto
Modalitati de livrare si plata
LIVRARE
In Cluj-Napoca
-
- Predare personala in max. 2 zile lucratoare
-
- Prin Curier rapid - 24 Lei in max. 3 zile lucratoare
In Romania:
-
- Prin Curier rapid - 24 Lei in max. 3 zile lucratoare
PLATA
- - La predare
- - Ramburs
- - Avans
Politica de retur
- - Produsul se poate returna in maxim 14 zile lucratoare
- - Metoda de retur: Ramburs contravaloare produs
- - Costul transportului va fi suportat de catre cumparator
- - Alte detalii: Retur acceptat in conditiile Garantiei de Livrare
Optiunea ta
Interfata diagnoza VAG COM VCDS v 22.10 EN - HQ - Vw Audi Skoda Seat 2023
Nu ai gasit ce cautai?
Instaleaza aplicatia Okazii.ro
