Controler L298N dual punte H pentru motoare pas cu pas stepper
Cost unic de transport la toate comenzile acestui vanzator
-
Produs:Nou, Fără garanție
-
Numar articol:202929443
-
Disponibilitate:Indisponibil
-
Preț:26,00 Lei
-
Anuntul a expirat la:10.11.2020, 00:30
-
Ai o nelamurire?
-
Vandut de:
-
Vinde si tu:Pune in vanzare un produs ca acesta
-
Optiuni:
Descriere
Vânzatorul este direct răspunzator pentru produsul afișat în această pagină.
Disponibilitate: Indisponibil - Vezi produse similare
Specificatii
L298N：
Module name : dual H
bridge motor drive module
Work mode
: H bridge drive (double road)
Main control
chip : L298N
Packaging
: electrostatic bag
Logical voltage
: 5V
Drive voltage :
5v-35v
Logical current
: 0mA-36mA
Driving current
: 2A(MAX single bridge)
Storage
temperature : - 20 ℃ to + 135 ℃
Maximum power
: 25W
Peripheral dimensions
: 43*43*27mm
This module USES
L298N as the main drive chip, with strong driving ability, low heat
and strong anti-interference ability.
Through this module
can use the built-in 78 m05 drive power supply parts of their work,
but in order to avoid the voltage regulator chip damage, when using
the driving voltage is greater than 12 v, please use the external
power supply 5 v logic.
This module USES a
large capacity filter capacitance, a continuation protection diode,
can improve reliability.
Notes:
1. When you are
driving voltage (above logo for the 12 v input, can actually accept
input range is 7 to 12 v) for 7 v to 12 v, can make to onboard
power supply 5 v logic, when using the onboard after 5 v power
supply, interface of + 5 v
The power supply does
not input voltage, but can yield 5V voltage for external
use.
2. When the driving
voltage is higher than 12V, it is less than or equal to
24V
(the chip manual
proposes to support 35V, but according to the
book
When the maximum
voltage is applied to the maximum voltage of 298 conservative
applications to 24V, for example, the motor with a rated voltage of
18V shall be driven.
You must first remove
the board 5V output to enable the jumper cap. Then 5V is accessed
outside the 5V output port
The 5V enables the
power to be a control signal with a level of 5V. When the signal
input is valid, and when the power supply is normal in the motor
drive module, the motor drive module outputs the current.
Otherwise, even if the power supply is normal, there is no current
on the motor.
Voltage to L298N
internal logic circuit power supply. (this is a high-pressure,
unconventional app!)
Module name :
dual H bridge motor drive module
Work mode
: H bridge drive (double road)
Main control
chip : L298N
Packaging
: electrostatic bag
Logical voltage
: 5V
Drive voltage :
5v-35v
Logical current
: 0mA-36mA
Driving current
: 2A(MAX single bridge)
Storage
temperature : - 20 ℃ to + 135 ℃
Maximum power
: 25W
Peripheral dimensions
: 43*43*27mm
This module USES
L298N as the main drive chip, with strong driving ability, low heat
and strong anti-interference ability.
Through this module
can use the built-in 78 m05 drive power supply parts of their work,
but in order to avoid the voltage regulator chip damage, when using
the driving voltage is greater than 12 v, please use the external
power supply 5 v logic.
This module USES a
large capacity filter capacitance, a continuation protection diode,
can improve reliability.
Notes:
1. When you are
driving voltage (above logo for the 12 v input, can actually accept
input range is 7 to 12 v) for 7 v to 12 v, can make to onboard
power supply 5 v logic, when using the onboard after 5 v power
supply, interface of + 5 v
The power supply does
not input voltage, but can yield 5V voltage for external
use.
2. When the driving
voltage is higher than 12V, it is less than or equal to
24V
(the chip manual
proposes to support 35V, but according to the
book
When the maximum
voltage is applied to the maximum voltage of 298 conservative
applications to 24V, for example, the motor with a rated voltage of
18V shall be driven.
You must first remove
the board 5V output to enable the jumper cap. Then 5V is accessed
outside the 5V output port
The 5V enables the
power to be a control signal with a level of 5V. When the signal
input is valid, and when the power supply is normal in the motor
drive module, the motor drive module outputs the current.
Otherwise, even if the power supply is normal, there is no current
on the motor.
Voltage to L298N
internal logic circuit power supply. (this is a high-pressure,
unconventional app!)
Modalitati de livrare si plata
LIVRARE
In Bucuresti
-
- Predare personala - regie in max. 2 zile lucratoare
PLATA
- - La predare
- - Ramburs
Politica de retur
- - Produsul nu se poate returna.
Nu ai gasit ce cautai?
Instaleaza aplicatia Okazii.ro
